The ACT-1 contains all of the functions required for studying and experimenting with active filters, operational amplifiers and other analog circuitry. The ACT-1 is a complete analog training instrument which is compact, lightweight and extrem

Features:

       Unconditional Life-time guarantee on all breadboarding sockets & 3-year warranty on all parts and workmanship.

       Ideal for analog, digital and microprocessor circuits

       New high & low buffered logic indicators

       8 channel logic monitor

       New 8 selectable logic switches

       Function Generator with continuously variable sine, square and triangle waveforms and TTL pulses

       Triple output power supply offers fixed 5 VDC supply plus two variable outputs: ±1.3 to ±15VDC

       Two Digital Pulsers

       Audio experimentation speaker

       New removable breadboard area and optional additional breadboard socket plates

       Multiple features in one complete test instrument saves hundreds of dollars necessary for individual units

Now, AC/DC, linear and digital electronics courses can be effectively taught with one economical trainer. With C.A.D.E.T, cluttered lab benches and time-consuming rebuilding of repeatedly used connections are eliminated. Students are able to concentrate their time and effort on specific circuits being studied. The C.A.D.E.T. improves efficiency and it costs far less than buying seperate trainers. It will immediately fit into your current curriculum and permit you to make better use of laboratory time.

Function Generator:
Frequency Range: 0.1 Hz to 100 kHz in six ranges.
Output voltage: 0 to ±10V (20Vp-p).
Output Impedance: 600 ohms (except TTL).
Output current: 10mA maximum, short circuit protected.
Output waveforms: Sine, Square, Triangle, TTL.
Sine wave: distortion <3% (10Hz to 100kHz).
TTL pulse: rise and fall time <25 nS. drive to 10 TTL loads.
Square wave: rise and fall time <1.5µS

Switches:
Two SPDT slide switches, all leads available and uncommitted. 8-pole DIP switch: one side of all eight switches connected and switchable to +5V or ground, other side of all eight switches separate, available, and uncommitted.

Breadboarding Area:
Three UBS-100 sockets with 840 tie-points each for a total of 2520 uncommitted tie-points. Two QT-59B Bus strips internally connected to power and ground. Fifty tie-points each for +5V, +V,=15 V and ground.

Logic Indicators:
8 LED's, active high, 1.4 volt (nominal) threshold, inputs protected to ±20 volts.

Debounced Push-Button (Pulsers):
Two pushbutton-operated, open-collector output pulsers, each with one normally-open, one normally closed output. Each output can sink up to 250 mA.

Potentiometers:
One 1 K ohm, one 10 K ohm, all leads available and uncommitted.

BNC Connectors:
Two BNC connectors, pin available and uncommitted, shell connected to ground.

Speaker:
0.25W, 8 ohms

Weight:
PB-503: 7 lbs;
PB-503C: 7 lbs, 13 oz.

Overall Dimensions:
PB-503: 6.5" H x 16" W x 11.5" D
PB-503C with case: 14" H x 19" W x 7" D

Power:
3-wire AC line input (117V, 60 Hz typical) with power-on indicator. Both Models are available in 220-240VAC@50Hz
Fixed DC output: +5V@1.0A, ripple <5mV.
Variable DC output: +1.3 V to +15V@0.5A, ripple <5mV.
Variable DC output: -1.3V to -15V @ 0.5A, ripple <5mV.

Click image to enlarge

E&L CADET II

Features:

       Expanded Removeable breadboard area

       Two open collector pulsers

       Built-in multi-waveform function generator

       Quad voltage power supply: Three DC & one low voltage AC

       Functions with optional electronics trainer boards

       Built-in logic probe with pulse capture

       BCD to 7 segment decoder/display

       8 channel logic indicatorsSpecifications

The C.A.D.E.T. II is a Complete Electronics Trainer that includes all the functions needed to teach basic AC/DC, Linear and Digital Electronics courses. The unit contains all the functions of our highly acclaimed original C.A.D.E.T. plus frequently requested features from educators worldwide.

The breadboard area is 33% larger than original C.A.D.E.T., holds up to 32 IC's and comes standard as a removable socket plate with velcro. If you prefer, it can be ordered withour bread boards for use with the extensive line of E&L Trainer Boards. The built-in logic probe will detect narrow logic pulses and eliminate the need for extra lab equipment. The BCD to 7 segment display/decoder saves students time when constucting circuits. The Quad Voltage Power Supply has +5 VDC, two variable DC outputs, and a fixed 12.6 VAC center tapped output. The trainer also includes 8 TTL compatible logic switches and two pulsers.

Function Generator:
Frequency Range: 0.1Hz to 100KHz in six ranges
Output voltage: 0 to +10V (20Vp-p)
Output Impedance: 600 ohms (except TTL)
Output current: 10 mA max., short circuit protected.
Output waveforms: Sine, Square, Triangle, TTL
Sine wave: Distortion <3% (10Hz to 100KHz)

Logic Probe:
Built-in TTL/CMOS compatible logic probe. Captures fast single shot events and pulse trains. Input impedance 300K, overload protection +50VDC, min. detectable pulse width 100nsec. TTL threshold low +0.8V high +2.25V, CMOS threshold low +30%Vcc high +70%Vcc. Memory mode, latches on first transition and LED remains on until probe is reset.

Breadboarding Area:
A total of 3360 uncommitted tie-points, available on velcro breadboard plate. Two QT-59B, bus strips. Fifty tie-points for each +5V, variable +15V, and ground if desired.

Logic Switches:
8 individual SPDT logic switches, one side of all eight switches connected and switchable to +5V or ground, other side of all eight switches separate, and uncommitted.

Logic Indicators:
16 LED’s 8 red to indicate logic high, 8 green to indicate a logic low.

Debounced Push-Button (Pulsers):
Two push-button operated, open-collector output pulsers, each with one normally-open and one normally- closed output. Each output can sink up to 25mA.

Potentiometers:
One 1K, one 10K, all leads available and uncommitted.

BNC Connectors:
Two BNC connectors, pin available and uncommit-ted, shell connected to ground.

Speaker:
0.25W, 8 ohms

Enclosure:
Steel case

Weight:
10 lbs. (4.5kg)

Overall Dimensions:
4.5” (H) x 15” (W) x 10.75” (D) (11.4 x 38.1 x 27.3 cm)

Power:
3-wire AC line input (115V/230V 50-60Hz or 230V 50Hz)-(specify when ordering ) with power indicator.

Power Supplies:
Fixed DC output: +5VDC @ 1.0A, ripple <5mV
Variable DCO/P: +1.3V to +15V @ 0.5A, ripple <5mV
Variable DCO/P: -1.3V to -15V @ 0.5A, ripple <5mV
Fixed AC O/P: 12.6 VAC Center tapped @ 100mA

BCD to 7 Segment Display:
2 BCD to 7 segment display circuits are provided including decoder/driver circuitry. Tie points: 5 per each unit.

TTL Pulse: Rise and fall time <25ns
Drive 10 TTL loads
Square wave: Rise and fall time <1.5µs

Switches:
Two SPDT slide switches, all leads available and uncommitted.

The LD-2 PENCILBOX Logic Designer/ Trainer permits students to avoid the repetitive building of frequently used circuits. All functions are internally connected to three solderless interconnect sockets with two tie points for each signal. The LD-2 comes complete with psu adaptor.

Click image to enlarge

The low cost LD-1 Pencilbox Logic Trainer permits students of digital electronics to make efficient use of valuable laboratory time. Circuits such as clocks, switches and lights are permanent parts of the LD-1 and need not be repeatedly constructed. Students build only those circuits which directly pertain to a particular experiment.

Everything required to design and experiment with logic circuitry is included in the Pencilbox. Power is supplied by either foyr 1.5v batteries or an optional AC adapter. The LD-1 is housed in a tough molded plastic carrying case with an integral hinged cover which stacks conveniently for storage.

The ECLIPS is one of the most versatile pieces of PLC training equipment available today. You simply specify which, and how many, modules you need built in to your trainer and we supply it to you ready to use – complete with appropriate training manuals. This way you only pay for what you actually need. Ordering Information

PLC / PLC Communications Module
This allows for one PLC to communicate with another in peer-to-peer mode. Fits directly to the PLC.

PLC Master / Slave Communications Module
A low cost way to start making your PLC communicate with another PLC for Master / Slave mode. Fits directly to the PLC.

Further Add-ons

       Extra Digital Inputs Block (16 DC Inputs)

       Extra Digital Outputs Block (16 Relay Outputs)

       Temperature Input (requires 8 inputs)

       Thermocouple Input (requires 8 inputs)

       Stepper Motor Control (requires transistor outputs on PLC)

       Slave Interface for Profibus

       Master Module for ASi Network

       RS232 Port. For communicating with any RS232 device (for example, bar code reader)

       PLC to HMI cable. For connecting PLCs to HMIs

       HMI Programming Software: PC based Windows Software for programming any of our ‘E’ series HMIs

Advanced PCL Programming (Using Mitsubishi PLC's)

Covering the Following:

       More Safety

       Advanced Programming Instructions (e.g. Add, Subtract, Compare, etc.)

       Ladder and SFC (Sequential Function Chart)

       Data Registers

       Motor Control

       Counter and Delay Programmes

       Shift Registers

       Index Registers

       Sub-routines

       Interrupts

       Multimode Programming

       Floating Point Arithmetic

       Analogue to Digital (ADC)

       Digital to Analogue (DAC)